tomek

Dairy part of Umerican junk diet,,,,,,,high on Ozempic brain fog today?

The thing is those are reather one time only, and you gotta get diameter close enough. While screw type if it way too big you can leave it, or cut off excessive whatever. I do agree for small diameter crimp types clamp batter.

Mirka is excellent brand as well.

3M cubitron. It might have the highest cost per piece but overall it is the least expensive to use. It is the shit. Trust me. Forget HF. One thing to remember, cheaper brands don't have consistent grain size, so, let's say 400 is actually collection of anything from 320 to 500,etc. It essentially gonna put some deeper scratches on your finish. So after sanding with cheap 400 there will be some deeper 320 cuts on the finish that might show after whatever you sprayed on it after sanding. Sandpaper is not where you wanna save money. Cheap shit is pretty much useless IMHO.

Hot 🔥 jalapeno? Looks delicious.

Just please continue. Post, for fuck's sake, something on the subject. I yield the floor to whoever or Carlos and Oscar. Share with us your knowledge and your thoughts.

I've decided to bail out from this thread for obvious reasons. What is stoping you, and your brother with years of experience on valvetrain gained from working on two stroke leaf blowers, from continuing on this subject? Am I necessary to discuss valvetrain? Unreplaceable? Can't do without me? Wtf?

Btw, blood pressure. I've reduced coffee to just one cappuccino first thing in the morning. Green tea on the afternoon. That's my entire caffeine intake for the day. Quality of sleep increased bigly. Like a brick. Reduced alkohol intake to occasional glass of red wine- combined less than a battle per week. Reduced salt. Got serious about pretty strenuous cardio about 4 times per week. At the begining my heart beat was approaching about 160 bpm by the end of exercise. After couple of months of it - 135 to 140. My blood pressure dropped about 15 points, and now is at 65/115. My resting heart rate is around 60 bpm.

Jb weld will eventually fail,something about different rate of temperature expansion vs. plastic. Been there, done that. So weld it. Now, if you have to pay someone else to repaint it- better to buy new piece from BMW.

Not sure about being default design. Fluid will flow even slower with bend like that. I don't have all day to watch oil slowly disappearing in the funnel. Not all of us live in places where average temperature is 120 F, and consequentry most automotive fluids have almost no viscosity even at room temperature. But anyway, I'd definitely get one for those special occasions.

Nope. That was supposed to be about 2004 r1. I nuked that one due to idiotic comments by certain idiot. Again. This one, was a trial balloon. I was hoping, perhaps, he learnt something, and would refrain from spreading stupidity. Nope. Nothing changed. It is pointless, it always comes to debunking utter nonsense he posts, etc instead of concentrating on the built. And he has major issue with the truth. Makes things up, twists the truth, etc. Inferiority complex on top of it. Probably was abused by parents and/or Swamp. We'll never know. He is destructive prick and asshole. Never starts anything of his own, but pollutes my threads with his bithering nonsense any chance he gets. Next trail balloon will be in 10 years. 🤪

Of course I do. The bike in question has oval pistons, so there are, at least, couple ways to play it. 😜

Oval? 😉

Superhawk and Swamp. Please continue without me. Please share your wealth of knowledge with other forum members.

I remember awhile ago you were absolutely "mind bugled" by fact piston travels slower-on averege- between TDC and 90 deg. ATDC vs. 90 deg. ATDC and BDC. That is very basic geometry, kind of like 2+2 =4 It was clear indication you don't know much about geometry, and consequently this particular area of physics. I would never, ever try to post anything into Swamp's IT threads becouse it would quickly become obvious I know dick about it, and cannot contribute in any meaningful way. I have no idea why both of you try to post something in threads like this one, when it is clear it is not your area of expertise. This is physics and hard science, it is not possible to bull shit your way out of it.