merc85 Posted June 22, 2021 Share Posted June 22, 2021 (edited) Hi peeps, thankyou for having me, I've just picked up a Blackbird, 1999 9,600 mile on her, FSH 1 owner, I think the ECU is on the way out as now and again im getting code 25 with the Side stand down. SO im looking for a ECU but don't know if my bike has HISS or not? It doesn't have HISS on the Ignition key surround just says HONDA Thankyou in advance Edited June 22, 2021 by merc85 Quote Link to comment Share on other sites More sharing options...
superhawk996 Posted June 22, 2021 Share Posted June 22, 2021 As far as I know none of them have HISS, at least not in the USA. As for your code, I doubt it's the ECU. Quote Link to comment Share on other sites More sharing options...
singram Posted June 22, 2021 Share Posted June 22, 2021 That and I believe it actually says HISS on the ignition- I wonder why no HISS in the US? Cost? Quote Link to comment Share on other sites More sharing options...
SwampNut Posted June 22, 2021 Share Posted June 22, 2021 Much lower rate of theft. Quote Link to comment Share on other sites More sharing options...
merc85 Posted June 22, 2021 Author Share Posted June 22, 2021 (edited) Sorry peeps I should have said it’s a U.K. bike. Code 25 is knock sensor, anyone on here had this ? Edited June 22, 2021 by merc85 Quote Link to comment Share on other sites More sharing options...
singram Posted June 22, 2021 Share Posted June 22, 2021 Looks non-HISS to me, but I'll defer to more knowledgeable members. As an aside, thats a smoking Blackbird! I'll trade you the mint Red one I just acquired. jk, LOL! Quote Link to comment Share on other sites More sharing options...
merc85 Posted June 22, 2021 Author Share Posted June 22, 2021 Thankyou buddy for the kind comment , she does have the key symbol in the rpm counter with green light so I assume that’s Hiss ?? Quote Link to comment Share on other sites More sharing options...
fizzy Posted June 22, 2021 Share Posted June 22, 2021 Key symbol on the dash is HISS, yes. As far as code 25, or knock sensor, it won't be the knock sensor. This is a not uncommon malady of the analog dash FI bikes. Possible causes of code 25: 1. ECU not strapped down 2. 2 large ECU multi pin connectors..... pins not 100% clean 3. 2 large ECU multi pin connectors.....wires/pins damaged. maybe due to cause 1. 4. "Loom fix" There is a connector buried in the loom under tape (LHS near battery) that corrodes. Can be fixed. 5. Bad ECU 6. Bad knock sensor or knock sensor wiring. The knock sensor wire has a braided sheath that is grounded. Check the wire. Bad knock sensor, unlikely, but possible I guess. Question, does the bike run normally. ? Power, fuel economy etc.? 1 Quote Link to comment Share on other sites More sharing options...
merc85 Posted June 22, 2021 Author Share Posted June 22, 2021 Bike runs a little flat more so wen cold, wen the light is on she is a little on off the throttle below 2.5k we all know how smooth these bikes should be. Thanku for the above Quote Link to comment Share on other sites More sharing options...
XXitanium Posted June 22, 2021 Share Posted June 22, 2021 3 hours ago, fizzy said: 4. "Loom fix" There is a connector buried in the loom under tape (LHS near battery) that corrodes. Can be fixed. Quote Link to comment Share on other sites More sharing options...
XXitanium Posted June 22, 2021 Share Posted June 22, 2021 2000 has an amber light that comes on in the fuel gauge, not sure on the '99. Quote Link to comment Share on other sites More sharing options...
superhawk996 Posted June 23, 2021 Share Posted June 23, 2021 5 hours ago, merc85 said: Bike runs a little flat more so wen cold, wen the light is on she is a little on off the throttle below 2.5k we all know how smooth these bikes should be. In your first post you said the light comes on only with the side stand down, does it stay on after raising the stand and while riding? Does it ever flicker, or is it totally on or off? First thing I'd do is a wiggle the test with the bike running to see if the light comes on or flickers; wiggle the test connector, ECU connections, and knock sensor connector. If the side stand switch is connected to the test connector I'll bet that's where the problem is. Quote Link to comment Share on other sites More sharing options...
merc85 Posted June 23, 2021 Author Share Posted June 23, 2021 (edited) Hi, The light comes on whilst riding, I pull over flip side stand down to read the code. I disconnected the ecu last night to have a look at the pins and they are like brand new. Wiggled the ecu wires while bike was running and the light didn't come back on at the time the bike was ticking over. I went to work this morning this and got 500yds up the road and the light is back on code 25 Edited June 23, 2021 by merc85 Quote Link to comment Share on other sites More sharing options...
fizzy Posted June 23, 2021 Share Posted June 23, 2021 You didn't say if the ECU was strapped down. Anyway, make sure it is. Wiggling the wires at idle will not trigger code 25, she performs a self test on start up and revving, which for you = 500yds. Recommend #4 next, loom fix. Type in "loom fix" in the search function, top of page. With some hunting, you will find one with pics. This is where with some basic soldering skills, the junction block I mentioned before, is cut off and the appropriate wires soldered together. I did this on my bike (as the block was corroded) to fix a code 25. It worked for 10 000 miles. Then the code returned. Out of options, I bought a used ECU. Some posters have reported running issues with a code 25. I had none. Just very annoying. That's why I asked. If anyone knows of an outfit that can, and has, repaired a blackbird ECU for code 25, that would be good info. Moderator; I checked the forum called "important/useful" looking for loom fixes. There is one, but the pics don't work. Is there something you/we can do to make this useful again? Thanks Quote Link to comment Share on other sites More sharing options...
XXitanium Posted June 23, 2021 Share Posted June 23, 2021 3 hours ago, fizzy said: ...I checked the forum called "important/useful" looking for loom fixes. There is one, but the pics don't work. Is there something you/we can do to make this useful again? Thanks ...or just sticky it here in the Garage? There have been a few cases this year that were suspect. PORTERB123 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.