They are 3/4" drop straight down, dosen't seem like much but they make a world of difference! These brackets will clear catted OE exhaust.
You must trim or remove your feelers if you do any kind of spirited cornering!
These are made from T6061 aluminium.

Cost is $60 shipped to Stateside addresses.
$65 to the UK and most of Europe.

They can be ordered here: http://www.cyclefarkle.com/

These will be shipped by USPS First class mail.


Pics of kit installed:





Enjoy!

Install guide here: http://www.flyingferrets.eclipse.co.uk/inf...%20Footpegs.pdf

Install note: Some people have stated that the OE pin dosen't fit the bracket when installing on the bike. If the OE pin fits the bracket before installation on the bike it will fit on the bike, you just have to wiggle the bracket up while pushing the pin in.
It's a tight fit!


__________________

Blank page

paypal sent.

Paypal sent.

Snail mail went out today! Thanks

paypal sent,today.Thanks Robby

Hey Dave,
I've sent you a couple emails with no reply. My paypal was sent May 29 and you show here on the forum that the pegs have shipped. What's up?

I think you are misreading the column. I'm guessing that an "x" will be added under the "shipped" column once the brackets have shipped. I'm also guessing that machining and finishing these takes time.

-The use of the colon after "payment received" would indicate otherwise.
-"Shipped" didn't look like a column.
-"These are ready again" ............well, I took that to mean that they're ready. I'm aware of the machining and finishing process.

Aside from this is that he could have replied to any one of my emails.....I'm guessing.

If it helps any, Dave is quality people. You don't have anything to worry about. He is probably just busy.

That does help.... 'nuff said. Thanks.

Yes, Dave is doing this all for no profit. He should raise the price a little to ensure he doesn't lose $$ like on the first run of these but he is to nice.

"Received a Paypal from: Chris Kunstt,,,who are you on the board???"

He isn't able to put all the names with the board names.
Is this you?

No, that's not me. I tried to follow his correspondence rules.

I'm not into anyone losing money on their labor. If that's the case then I can understand not answering emails.

If the pegs are as good as everyone says, I have no problem paying additional $$ in order to make it worth his time and also to maybe encourage him to attempt some other projects that we can all benefit from.

Thanks for your input.

If anyone is just thinking about getting these, get them!

I spent alot of money to make my XX comfortable on Heli bars, pro grips, throttlemeister, double bubble, corbin seat, levers, throttle rocker....

The best money I spent was on these.

parafon, I PM'd ya a while ago,,,,you must not of got it, sorry.

You won't be dissapointed!

Dave

Thanks Dave. I didn't get the PM.
I'm with ya on this the rest of the way.

Tony

Dave any idea when these will go out?

Are any of these still available?

Sent out 25 today, more tomorrow.

Updated 1'st post.

Dave

I know, it's about time!

Same old problem again with the machine shop.

You have PM

Not to hijack the thread, but the newer VFR peg feelers match the stock bird look and are about 2/3 the length. Part # 90176-MCW-D00.

Upadted first post for recent shipped brackets.

(48 left to sell)

Dave

Thanks for the input.

Updated pg 1 again.

I got the brackets in the other day. Quality is top notch. I think these are going to really ease the pain I get in my knees...mainly my right one. I haven't done anything other than ride around the neighborhood with them yet but its definitely a change for the better. Another thing you guys with the stock pegs might do is get some aftermarket pegs. You probably gain up to .25" over the stockers since they don't have that big rubber pad on top. I haven't measured that or anything but it seems like it helped a bit when I replaced my stockers.

I got mine last week too. Very good quality machining. I thought I would try this method out instead of my Buell pegs. But do you think I could find my stock pegs in my garage? DOH!!! I'll keep looking.

Hey folks, I still have LOTS of these left!

Updated first post with pics as the original link dosent work.

Dave

Just sent you the money for a set through paypal. Can't wait to try them!

Got it!
And an order from Rhubarbray, thanks!

Still have 40 ish left!

Help a brother out, it's almost Christmas,,,,kinda.

Dave

+1 on this!!! I have all the same mods on my bike & brackets made the most difference on long runs. I got mine on the first batch. If you are 6'+ or have long legs, get these.

Larry

PM sent.

Paypal sent.

I bought a pair of these off someone else a while ago, and I love 'em. Problem is, I over-filed them during installation, and have been living with minor looseness ever since. No longer! Round two I won't be such a klutz.

Paypal sent.

Paypal sent

Money-order sent via snail mail. thanks! -Shane

Dave - You have PM.

Received and replied! Should go out tomorrow or Thursday.

Dave

Hey Dave, PM and PayPal sent!

Thanks!

Got 'em in the mail today. Awesome dave, thanks!

You may want to see if they fit a VFR, 600RR, 1000RR.

They could all use these. Each bike has it's own forum.

I thank you everytime I go out for a ride.

They only tppk a few days to get to the UK. Beautifully made, well packaged, and they work. As a bonus they allow better operating angles on my Translogic quickshifter. With the incredible dollar exchange rate they must be my best buy ever.

Bump

Still have lots of these left ya'all.

Dave,
Do you still have lowering brackets in stock? Can I send you a paypal payment?

Yeah, Dave, do you have any more left. And...uh.......the link on page one doesn't work. Can anybody help me with that original link. I think it was the installation how-to thread. I'd like to check it out before ordering.

Thanks,
Train

The Second Link lower down just above the names is the instal

Round two is sold out.

Round three will be available hopefully sometime in Feburary. I will start a new post then.

Thanks for all the support on these folks!

Dave

...same question as on page 2 - Is anyone familiar enough with the similarities between BB and '88 Hurricanes to guess if these will work on the Hurricane?

I'm 6'4 and this would be a great upgrade if they will work.

Tx
Bill

Round three is ready!

Going to keep this thread going as I linked to it from other sites!

Any questions, post up.

I am in this time,,,for two sets Dave.

I'm in as well.
I'll take one set.
Sent PM...

I'm in for a set.

I'll send you a PM.

Thanks man!!!!